Shop Storage

What Size Breaker for a 2 HP Dust Collector at 240V?

A 2 HP dust collector at 240 V is a 12 A load in NEC Table 430.248. The wire must carry 15 A, so 14 AWG NM-B is the minimum, and the breaker can run from the maker's 15 or 20 A up to 30 A. The receptacle sets the breaker in practice. The forum answer of 30 A on 10 gauge is legal but oversized.

Key takeaways

  • NEC Table 430.248 lists 12 A for any 2 HP single-phase motor at 230 V. The wire must carry 125 percent of that, 15 A, which 14 AWG NM-B cable does exactly.
  • The breaker may be anything from the maker's figure up to 250 percent of 12 A, which is 30 A. Grizzly asks for at least 15 A on its G1029Z2P and Jet for at least 20 A on its DC-1200VX.
  • A single receptacle on its own circuit must be rated at least as high as the breaker. Grizzly ships a NEMA 6-15 plug, so on one 6-15 outlet the breaker is 15 A.
  • 30 A on 10 gauge sits at the code's ceiling, not below it. It is legal with a 30 A receptacle or hardwiring. No maker checked asks for it.
  • A 2 HP motor on 120 V is a 24 A load in the same table, double the 240 V figure. Harbor Freight's 120 V, 2 HP collector lists 14 A and ships a 15 A plug.

Two answers circulate. The usual forum answer is a 30 A breaker on 10 gauge wire, the same circuit people run for a 3 HP saw. The other is to read the label: Grizzly's G1029Z2P lists 9 A and asks for a 15 A circuit. Both are legal. Neither starts where the code starts.

The National Electrical Code (NEC) sizes a motor circuit from a table, not from the label. Below, four 2 HP collectors are set beside that table. 30 A on 10 gauge sits at the very top of the allowed band. The bottom is half that.

The terms this answer turns on

2 HP is the motor's rated output in horsepower. On a dust collector it is the impeller motor, the only real load on the circuit.

The breaker is the double-pole breaker in the panel. It opens both hot wires of a 240 V circuit. On a motor circuit its job is to stop a short circuit or a ground fault. It does not protect the motor from running hot.

Nameplate amps are the current printed on the motor or in the manual. Grizzly calls it the "Full-Load Current Rating". It defines that as the current the machine draws "at 100% of the rated output power."

Table current is the figure NEC Table 430.248 gives every single-phase motor of a given horsepower and voltage. The code calls it full-load current, or FLC. It is the same for every brand.

Ampacity is the current a wire can carry all the time without overheating. It depends on the wire size and on its insulation's temperature rating.

Which current sizes the circuit? Open Exam Prep's guide to Article 430 is blunt: table current "MUST be used for sizing conductors, switches, and short-circuit/ground-fault protection." The nameplate is used "ONLY for sizing motor overload protection." So the wire and the breaker come from the table.

Worked through: Grizzly's G1029Z2P on 240 V

Take the Grizzly G1029Z2P, a 2 HP bag collector rated at 1550 CFM. Its manual lists 240 V single phase, a full-load current of 9 A and a minimum circuit size of 15 A. It ships with a 6 ft, 14 AWG cord and a NEMA 6-15 plug.

Step one, the table current. Table 430.248 gives 12 A for a 2 HP motor at 230 V. The circuit uses 12 A, not the 9 A on the label.

Step two, the wire. Section 430.22 sizes the wire at 125 percent of the table current:

12 A x 1.25 = 15 A

Cerrowire rates 14 AWG copper NM-B at 15 A. It passes, with nothing to spare. Mike Holt's EC&M article works this exact motor, a 2 hp, 230 V single-phase unit, and gets the same 15 A. Holt reads the 75 C column, where 14 AWG is 20 A.

Step three, the breaker ceiling. Table 430.52 allows an ordinary panel breaker, the inverse time kind, up to 250 percent of the table current:

12 A x 2.50 = 30 A

30 A is a standard size under 240.6(A), so no rounding is needed. Holt's example reaches the same 30 A.

Step four, the floor. Grizzly asks for at least 15 A. If the circuit is fused, it wants "a time delay fuse marked D."

Step five, the outlet. Section 210.21(B)(1) says "A single receptacle installed on an individual branch circuit shall have an ampere rating not less than that of the branch circuit." The plug Grizzly ships is a 6-15. One 6-15 outlet on its own circuit means a breaker of 15 A at most.

So, as shipped and plugged into one outlet, the G1029Z2P goes on a 15 A double-pole breaker and 14 AWG or larger wire, exactly what Grizzly asks for. Up to 30 A is allowed only with a 30 A outlet or with the collector wired in directly.

Four 2 HP collectors, one table

Every 2 HP, single-phase collector checked for this page, with the maker's own figures beside the code arithmetic:

CollectorListed currentAtMaker's circuit figurePlugTable 430.248Wire must carry, table x 1.25Nameplate x 1.25
Grizzly G1029Z2P9 A240 V15 A minimum circuitNEMA 6-1512 A15 A11.25 A
JET DC-1200VX8 A230 Vbreaker, plug and outlet at least 20 Anone supplied12 A15 A10 A
Laguna P-Flux 214 A220 Vnot statednone supplied12 A15 A17.5 A
Harbor Freight 5972614 A120 Vnominal 120 V circuitplug for up to 15 A24 A30 A17.5 A

The labels run from 8 to 14 A for the same 2 HP at 240 V. Grizzly and Jet sit below the table's 12 A. Laguna sits above it.

The Laguna row is the one to read twice. On the table, the wire must carry 15 A, and 14 AWG NM-B passes. On Laguna's own 14 A, 14 x 1.25 = 17.5 A, and 14 AWG NM-B fails. That case is worked below.

The Harbor Freight row is a different machine: a 2 HP motor built for 120 V. It has its own section.

The wire: 125 percent of 12 A

Cerrowire's chart, based on the 2017 NEC with no corrections applied, lists copper by insulation temperature:

Copper60 C (NM-B, UF-B)75 C (THW, THWN, XHHW)90 C (THHN, THWN-2)15 A, table17.5 A, Laguna label
14 AWG15 A20 A25 APasses, exactly in NM-BFails in NM-B; passes at 75 C
12 AWG20 A25 A30 APassesPasses
10 AWG30 A35 A40 APassesPasses

NM-B is the sheathed cable in most garage walls, and Cerrowire lists it only in the 60 C column. So in NM-B, the code minimum for a 2 HP collector at 240 V is 14 AWG.

14 AWG has no margin on the table figure, and it falls short of Laguna's label. 12 AWG NM-B, at 20 A, clears both readings for every 240 V collector in the table.

Is 14 AWG on a 30 A breaker really allowed? On a motor circuit, yes. The breaker guards against shorts, not overload. Holt's guide to the 2020 code says readers may be "uncomfortable" with Article 430's allowances, "such as protecting a 10 AWG conductor with a 60A overcurrent protective device." His 2 hp example puts 14 AWG on a 30 A breaker.

The breaker band: maker's floor to the code's ceiling

The ceiling is Table 430.52. Open Exam Prep lists 250 percent for an inverse time breaker on a single-phase motor, and 175 percent for a dual-element time-delay fuse. Where the result is not a standard size, the next standard size up is allowed. The standard sizes in 240.6(A) run 15, 20, 25, 30, 35 A and up.

ProtectionArithmeticLargest allowed
Inverse time breaker, 250 percent12 x 2.50 = 3030 A
Time-delay fuse, 175 percent12 x 1.75 = 21, next size up25 A

The floor is the motor's start. Holt says the device must be "capable of carrying the motor's starting current." His 2020 code guide puts start-up current at "typically six (or more) times the running current." No code table gives a collector's starting figure, so the makers set the floor. Grizzly says 15 A. Jet says "at least a 20 amp circuit breaker or fuse."

So the band is 15 to 30 A for the Grizzly and 20 to 30 A for the Jet. Laguna's page gives no circuit figure, and on the table its ceiling is the same 30 A.

Why may the breaker be so much larger than the running current? Because a separate device handles overload. Section 430.32, in Holt's words, wants it set to open at no more than "115% of the motor nameplate FLC rating" for a continuous duty motor over 1 hp. For the G1029Z2P that is 9 A x 1.15 = 10.35 A. That is where the label is used.

When the label outranks the table

The code has an exception, and it decides the Laguna row. 430.6(A)(1) Exception No. 3, in the 2008 text on Solar365, reads: "For a listed motor-operated appliance that is marked with both motor horsepower and full-load current, the motor full-load current marked on the name-plate of the appliance shall be used instead of the horsepower rating."

Where it applies, the nameplate sizes the wire and the breaker, not the table. For Grizzly and Jet that makes the circuit smaller than the table's. For Laguna it makes it larger: 14 A x 1.25 = 17.5 A, and the breaker ceiling becomes 14 x 2.50 = 35 A.

Whether a collector counts as a listed motor-operated appliance is the inspector's call. The manuals and the product page read here do not say. 12 AWG NM-B passes on either reading for all three 240 V units.

Is "30 A on 10 gauge" right?

It is legal, and it is the largest circuit the motor rules allow. 10 AWG NM-B, at 30 A, carries far more than the 15 A the wire needs. 30 A is exactly 250 percent of 12 A.

What the rule leaves out is the outlet. With one receptacle on the circuit, that receptacle must be a 30 A, NEMA 6-30. Grizzly ships a 6-15 plug, and Jet asks only for a plug and outlet rated "at least 20 amps." So 30 A means a 30 A outlet and a plug to match, or wiring the collector in directly. The cord itself is a separate question, covered under limits below.

The rule persists because it is the 3 HP answer. A 3 HP motor is 17 A in the same table and needs wire for 21.25 A, which is 10 AWG in NM-B, as worked in the 3 HP table saw breaker and wire guide. For a 2 HP collector, the same circuit is double the wire the code asks for.

The folk source: "10 gauge for 40 A intermittent"

The usual citation for oversized dust collector circuits is Bill Pentz's electrical page. Pentz writes that "10-gauge wire is rated for ongoing current loads up to 30 amps, or 40 amps if you are running intermittently loaded motors such as on a table saw or joiner." He recommends wiring a shop with "multiple 240V dedicated circuits."

His 30 A figure matches Cerrowire's 60 C column for 10 AWG. The 40 A figure does not appear in that column. Cerrowire's 40 A for 10 AWG is the 90 C column, the one for single wires such as THHN, not NM-B. Pentz also ties it to intermittent loads like a saw. A collector is the opposite case. Jet's manual notes that "dust collectors are generally used at the same time other tools are running."

For a 2 HP collector, the folk figure is beside the point anyway. A 40 A breaker would be over the 30 A ceiling of Table 430.52.

The 120 V case

A 2 HP motor on 115 V is 24 A in Table 430.248, double the 230 V figure. Same motor, same power, half the voltage, twice the current.

On the table230 V115 V
2 HP table current12 A24 A
Wire must carry, x 1.2515 A30 A
Breaker ceiling, x 2.5030 A60 A

On the table, a 120 V, 2 HP motor needs wire for 30 A, which is 10 AWG NM-B.

Harbor Freight sells one. Its item 59726 manual lists "120VAC / 60Hz / 14A" and "2HP, Single Phase". It is "for use on a nominal 120-V circuit" with a plug rated "for up to 125 VAC and up to 15 A." The label reads 14 A against the table's 24 A, 58 percent of it, which is the widest gap of the four collectors here.

Two circuit rules then apply to a plug-in tool on 120 V:

  • The 80 percent cap. Section 210.23 limits one cord-and-plug load on a circuit with other outlets to 80 percent of the breaker: 12 A on 15 A, 16 A on 20 A. The 14 A collector is over the cap on 15 A and under it on 20 A.
  • The outlet. Section 210.21(B)(3) allows 15 A receptacles on a 20 A circuit that has two or more receptacles. So the 15 A plug can go on a 20 A circuit.

That makes a 20 A circuit the fit for this collector. On the nameplate reading, under Exception No. 3, the wire must carry 14 x 1.25 = 17.5 A, so 12 AWG NM-B. On the table reading it must carry 30 A, so 10 AWG. As with Laguna, which applies depends on the listing.

A 15 A circuit shared with a saw is out of the question. The table saw and dust collector circuit guide sums those loads at 21 to 28 A.

Dual voltage: what rewiring changes

None of the four 2 HP collectors read here is dual voltage. Grizzly, Jet and Laguna list 230 or 240 V only, and Harbor Freight lists 120 V only.

Grizzly's 1.5 HP G1028Z2, in the same manual, shows how a dual voltage unit works. It lists 12 A at 120 V and 6 A at 240 V, and a 15 A circuit at either voltage. It ships prewired for 120 V with a 5-15 plug. Converting it means rewiring the motor in its junction box and fitting a 6-15 plug. Grizzly says the conversion "MUST be performed by an electrician or qualified service personnel."

The table shows the same halving for 1.5 HP: 20 A at 115 V, 10 A at 230 V.

The answer, collector by collector

Each row restates a ruling made above:

CollectorBreakerWire, NM-BOutlet
Grizzly G1029Z2P, as shipped15 A double-pole14 AWG minimum, 12 AWG for marginsingle 6-15
JET DC-1200VX20 to 30 A double-pole14 AWG minimum, 12 AWG for marginrated at least as high as the breaker, and at least 20 A
Laguna P-Flux 2up to 30 A on the table, no maker floor12 AWG, which passes the 14 A labelrated at least as high as the breaker
Harbor Freight 59726, 120 V20 A12 AWG if the label governs, 10 AWG on the table15 A receptacle on a circuit with two or more

Where this answer stops applying

  • Three-phase collectors. They use Table 430.250, not 430.248. Jet's three-phase DC-1200VX lists 6 A at 230 V. Nothing on this page applies to it.
  • The cord and the plug. Holt notes that flexible cord is sized under 400.5, a different rule. Grizzly and Jet ship a 14 AWG cord. This page does not rule on fitting a 30 A plug to it.
  • Hot or bundled runs. Cerrowire's figures carry no temperature correction or adjustment. A run through a hot attic, or bundled with other circuits, can need larger wire.
  • The 75 C column. It counts only where the wire type, the breaker and the terminals are all rated for it.
  • A breaker above the maker's figure. The band up to 30 A assumes the overload device required by 430.32 is there. If the manual does not show one, ask the maker before going above its circuit figure.
  • Laguna's floor. Laguna's page gives no minimum circuit, so no figure here says how small a breaker its motor will start on.
  • Local codes. Everything here is the NEC as published, and local amendments win. Grizzly and Jet both want an electrician to do the wiring.
  • Published figures only. Every current comes from the makers' manuals and pages. No collector was wired or measured for this page.

Planning the outlets

A collector runs while a saw does. Grizzly's circuit figures assume a dedicated circuit, and Jet says one "will give you the best results." So each machine gets its own. The same table method sizes the other big 240 V motor in many shops, the compressor, in the 60 gallon compressor breaker guide. Place both outlets before a wall system goes up, as the garage shop layout guide advises. If a collector has to reach a far corner on a cord, the extension cord gauge guide covers the voltage drop. Harbor Freight's own cord table puts a 12.1 to 16 A tool on 12 gauge at 50 ft.

The thirty-second check

  1. Read the horsepower and the voltage on the motor. For 2 HP, the table says 12 A at 230 V and 24 A at 115 V.
  2. Wire for 125 percent of that: 15 A at 240 V, so 14 AWG NM-B at minimum. Use 12 AWG if the label is above 12 A.
  3. Pick a breaker from the maker's minimum up to 30 A at 240 V.
  4. Match the outlet. One receptacle on the circuit must be rated at least as high as the breaker. A 6-15 means 15 A.
  5. Treat 30 A on 10 gauge as the ceiling, not the starting point.

Frequently asked questions

What size breaker do I need for a 2 HP dust collector on 240 V?

A double-pole breaker from 15 to 30 A. The floor is the maker's figure, 15 A for the Grizzly G1029Z2P and at least 20 A for the Jet DC-1200VX. The ceiling is 250 percent of the NEC table's 12 A, which is 30 A. The receptacle must be rated at least as high as the breaker if it is the only outlet on the circuit.

Can I use 14 gauge wire for a 2 HP dust collector?

Yes at 240 V on the table figure. The wire must carry 12 A x 1.25 = 15 A, and 14 AWG NM-B is rated 15 A. Laguna lists its 2 HP P|Flux 2 at 14 A, though, and 14 A x 1.25 = 17.5 A is more than 14 AWG NM-B carries. 12 AWG NM-B, at 20 A, passes on both figures.

Is a 30 amp breaker too big for a 2 HP dust collector?

Not under the motor rules. 12 A x 2.50 = 30 A, so 30 A is the largest inverse time breaker allowed. The catch is the outlet. A single receptacle on that circuit must be rated 30 A, which the 6-15 plug Grizzly ships does not fit.

Can a 2 HP dust collector run on 120 V?

Some are built for it. Harbor Freight's 2 HP collector, item 59726, is a 120 V machine at 14 A with a plug for up to 15 A. The NEC table puts a 2 HP motor at 24 A on 115 V. None of the four 2 HP collectors read for this page is dual voltage.

Do I need 10 gauge wire for a dust collector?

Not for a 2 HP at 240 V. The wire needs to carry 15 A on the table figure, or 17.5 A on Laguna's 14 A nameplate. 10 AWG is fine, since larger wire is always allowed, but it is not required.

Does a dust collector need its own circuit?

Both manuals that address it point that way. Grizzly says its circuit figures apply to a dedicated circuit with one machine running at a time. Jet says a dedicated circuit "will give you the best results", since collectors run while other tools are running.

Sources and references

  1. Grizzly, G0548ZP, G1028Z2 and G1029Z2/G1029Z2P dust collector owner's manual (mfd. 08/18+, revised August 2018) G1029Z2P 2 HP, 240 V single phase, full-load current 9 A, minimum circuit size 15 A, NEMA 6-15 plug, 14 AWG cord; time delay fuse marked D if fused; circuit requirements apply to a dedicated circuit; full-load current is not the maximum draw. G1028Z2 1.5 HP, 12 A at 120 V and 6 A at 240 V, 15 A circuit at either voltage, prewired 120 V with a NEMA 5-15 plug; conversion to 240 V rewires the motor and fits a 6-15 plug, done by an electrician or qualified service personnel
  2. JET, DC-1200VX series dust collectors operating instructions and parts manual, M-710701, revision C1 09/2018 2 HP, 1 PH, 230 V only, 8 A, 60 Hz; not supplied with a plug; plug and outlet rated at least 20 amps; circuit protected by at least a 20 amp breaker or fuse; a dedicated circuit gives the best results since collectors run while other tools are running; 14 AWG power cord
  3. Laguna Tools, P|Flux 2 dust collector product page 2 HP motor, 220 V, 60 Hz, single phase, 3450 RPM, running current 14 A at 220 V (6 in inlet); 1740 CFM maximum; no plug included
  4. Harbor Freight Tools, 2 HP dust collector owner's manual, item 59726 (2024) 120 VAC, 60 Hz, 14 A, 2 HP, single phase, 1550 CFM; for use on a nominal 120 V circuit; 3-prong plug for up to 125 VAC and up to 15 A; no adaptor; extension cord table for 12.1 to 16.0 A
  5. Open Exam Prep, Motor full-load current and conductor sizing study guide (NEC Article 430) Table 430.248 at 115 and 230 V, 1.5 HP 20.0 and 10.0 A, 2 HP 24.0 and 12.0 A, 3 HP 34.0 and 17.0 A; table FLC must be used for conductors, switches and short-circuit and ground-fault protection, nameplate only for overloads; conductors at table FLC x 1.25 (430.22)
  6. Mike Holt, Motors and the NEC, EC&M (2013) 2 hp, 230 V single-phase example, 12 A x 1.25 = 15 A on 14 AWG rated 20 A at 75 C, and 12 A x 2.50 = 30 A inverse time breaker; overloads at no more than 115 percent of nameplate, 125 percent with a 1.15 service factor (430.32); short-circuit device must carry the starting current; locked-rotor current often six times full-load
  7. Mike Holt, Understanding the 2020 National Electrical Code, Volume 1, section 430.6 Table FLC used for conductor sizing and branch-circuit short-circuit and ground-fault protection; nameplate FLA not permitted for those except other than continuous duty; motor start-up current typically six or more times running current; Article 430 allows a 10 AWG conductor on a 60 A device
  8. Solar365, NEC 2008 Article 430, 430.6(A)(1) exceptions Exception No. 3, a listed motor-operated appliance marked with both horsepower and full-load current uses the nameplate full-load current for the conductors, the disconnect, the controller and the short-circuit and ground-fault protection
  9. Open Exam Prep, Motor branch-circuit short-circuit and ground-fault protection (Table 430.52) Single-phase motors, inverse time breaker 250 percent, dual-element time-delay fuse 175 percent of table FLC; next higher standard rating permitted
  10. ExpertCE, NEC standard circuit breaker sizes 240.6(A) standard ratings 15, 20, 25, 30, 35, 40, 45, 50, 60 A and up
  11. Cerrowire, Ampacity charts Copper 14, 12 and 10 AWG at 15, 20 and 30 A in the 60 C column (NM-B, UF-B), 20, 25 and 35 A at 75 C (THW, THWN, XHHW), 25, 30 and 40 A at 90 C (THHN, THWN-2); 2017 NEC, no correction or adjustment
  12. Open Exam Prep, Branch-circuit ratings, conductor sizing and multiwire circuits (section 6.1) 210.21(B)(1), a single receptacle on an individual branch circuit rated not less than the circuit; 210.21(B)(3), 15 or 20 A receptacles on a 20 A circuit with two or more receptacles, 30 A on 30 A
  13. Open Exam Prep, Branch circuit ratings and sizing study guide (Idaho electrician) 210.23(A)(1), one cord-and-plug load not fastened in place at no more than 80 percent of the circuit, 12 A on 15 A and 16 A on 20 A
  14. Bill Pentz, Dust collection electrical 12-gauge wire rated for ongoing loads up to 20 amps; 10-gauge up to 30 amps, or 40 amps for intermittently loaded motors such as a table saw or jointer; 8-gauge up to 50 amps; 240 V for motors of 1 hp or larger; recommends multiple 240 V dedicated circuits

Last reviewed and updated November 19, 2026. Figures on this page come from published specifications, standards and stated derivations. See how we analyze and our corrections policy.